DataSheet: PDF icon BCPDF. BC is a general purpose PNP transistor. It is used in switching and amplifier applications. The DC current gain varies in. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. Semiconductor data sheets and/or specifications can and do vary in different applications . BC / BC / BC VCE = -5 V, IC = µA.

Author: Goltikus Arashill
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Environment
Published (Last): 10 November 2017
Pages: 235
PDF File Size: 19.87 Mb
ePub File Size: 14.94 Mb
ISBN: 857-7-28272-269-4
Downloads: 99165
Price: Free* [*Free Regsitration Required]
Uploader: Moogutaxe

When base current is removed the transistor becomes dataxheet off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. It is used in switching and amplifier applications. Interface SD Card with Arduino.

Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that is to be switched. Virgin Galactic — Commercial Space Flight.

BC Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

Complete Technical Details can be found in the Teansistor datasheet given at the end of this page. When daatasheet as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration. Skip to main content. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

  LIBRO TRAICIONADA DE P.C.CAST Y KRISTIN CAST PDF

Transistor BC558

It is also used as a complement for transistors BC to BC BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin. Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers. It can amplify power, voltage and current at different configurations. Submitted by admin on 26 March The BC because of this large gain value is normally used to as a audio amplifier.

BC Transistor | BC Datasheet

In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal. When this transistor is fully biased then it can allow continues current transostor mA to flow across the collector and emitter. Interface GPS with Arduino. BC is a general purpose PNP transistor.

BC558 Datasheet, Equivalent, Cross Reference Search

The value of this resistor RB can be calculated using below formulae. The input signal at base is amplified and taken at the emitter.

Arduino based GPS receiver. SPI Module of Arduino. In the absence of base signal, it gets completely off. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can datasheett achieved by supplying the required amount of current to the base pin.

  LIBRO TEOLOGIA SISTEMATICA MYER PEARLMAN PDF

TL — Programmable Reference Voltage. The voltage divider is the commonly used biasing mode.

Choosing Battery for Robots. What is Web Browser. This high-density System-in-Package SiP integrates controller, power switches, and support components.

Amplifier modules like Audio amplifiers, signal Amplifier etc. The DC current gain varies in range to BC is used in common emitter configuration for amplifiers.

The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. A Transistors acts as an Amplifier when operating in Active Region.

For amplification applications, the transistor is biased such that it is partly on for all input conditions. Choosing Motor For Robots. BC as switch Datahseet a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

This is known as the biasing. A resistor is always added in series with base pin to limit transistir base current. BC has a gain value of to ; this value determines the amplification capacity of the transistor.